Adaptronic M1200 Modular ECU – 4 Cylinder / 2 Rotor

$990.00

This is the Adaptronic M1200, the entry to the new Modular range offered by Adaptronic. It replaces the e420d for 4-cyl /2-rotor engines using the technology from Adaptronic’s new Modular ECUs.

Categories: , , SKU: 10101

Description

This is the Adaptronic M1200, the entry to the new Modular range offered by Adaptronic. It replaces the e420d for 4-cyl /2-rotor engines using the technology from Adaptronic’s new Modular ECUs.

Adaptronic’s main objective with the Modular ECU line is to work towards Adaptronic’s mission to give people control. In doing this, Adaptronic came up with a system which would give people greater flexibility.

Features / Specifications

Control board

Variable Number Details
Analogue 0-5V inputs 11
  • 2 x TPS
  • 1 x ext MAP (can use in conjunction)
  • 4 x temp (pullup select)
  • 1 x 0-5V aux
  • 2 x pressure (oil / fuel)
  • 1 x analogue O2 (max 5V)
Analogue oxygen sensor inputs 1 Each can be either:

  • 0 – 5.5V, 55k input impedance
  • 0- 3.3V, 1M input impedance
Temperature inputs 4 Each is 0 – 5.5V, 55k input impedance to ground
Each can be:

  • Non-biased, eg in piggyback mode. Calibration is in mV
  • Biased, calibration is in Ohms. 3 internal pull-ups, 1k5, 2k2, 4k7, automatically selected by the ECU

Manifold air temperature, coolant temperature, oil temperature, fuel temperature

Crank trigger inputs 3
  • Selectable 2k2 pullup (on in digital mode, off in reluctor mode)
  • Variable voltage trigger threshold from 0 to 65V – either arm input for reluctor or threshold for digital input
  • AC coupled zero crossing trigger in reluctor mode
  • Variable filtering 1 to 192 µs
  • See built-in scope section
Vehicle speed input 1
  • Selectable 2k2 pullup
  • Variable voltage trigger threshold from 0 to 65V
  • Variable filtering 1 to 192 µs
  • See built-in scope section
Sensor power and ground
  • 5V regulated output for sensors, max 100 mA, current limited (voltage is monitored by ECU)
  • Sensor ground connected to ground inside ECU under firmware control to detect external ground loops in the wiring (voltage is monitored by ECU)
Knock inputs 1
  • 50 k input impedance
  • Sampled at 80 kHz (12-bit resolution, 3.3V peak to peak max voltage),
  • Variable second order highpass and lowpass filters
  • Selectable start and end of sampling windows (in crank angle)
Wired Outputs 2
  • Dedicated outputs for tacho and EFI relay
  • Tacho output has inductor to generate back-EMF spike for impulse tachometers.
Headphone output 1 Mono output, can be selected as direct knock input or filtered knock input
Power sources 3 ECU can be powered by 12V EFI input, ignition switch, or USB (USB for settings / firmware upgrades / log retrieval only; 12V must be applied to read inputs)
CAN channels 2
  • Up to 1 Mbps
  • Internal 120 Ohm terminating resistor can be turned on and off with ECU setting on each channel
USB connection 1
  • Standard USB mini AB connector.
  • 12 Mbps max speed
  • USB appears as mass storage device (USB stick); no drivers are necessary
  • Software installer included on mass storage device
Serial connections 4
  • 2 serial in
  • 2 serial out
Inbuilt sensors
  • Microphone
  • 3 axis accelerometer
  • 3 axis rate gyro
Inbuilt logging 32 MB
  • Max 30 hrs @ 10 Hz, 13 channels
  • Min 20 mins @ 100 Hz, 125 channels
Built-in scope 4 channels
  • Max sample rate 200 kHz (5µs sample period)
  • 1000 samples per screen (min 5ms across the screen)
  • Analogue trigger inputs sampled at 40 kHz

Channels include

  • Analogue CAS inputs
  • Peak detected CAS voltages
  • CAS threshold voltages
  • Filtered CAS inputs
  • Analogue external inputs
  • Raw and filtered knock waveforms
  • Current engine angle
  • Calibrated input values
  • Intermediate calculation values
  • Output calculated values
Main loop execution speed Variable depending on tuning mode and corrections enabled, 400 Hz nominal

Main Output Module

Number of injector outputs 4
  • Switching topology for low heating
  • Peak and hold current waveforms
  • Programmable peak and hold current
  • Max current per channel 4A continuous
  • Nominal current per channel 1A (can be controlled in software)
  • Unused injector outputs can NOT be configured as auxiliary outputs
  • Output voltage and current monitored
Number of ignition outputs 4
  • Appears as a 470 Ohm to supply when high, short to ground when low
  • Current limited output
  • Unused injector outputs can NOT be configured as auxiliary outputs
  • Voltage and current monitored
Number of aux outputs 7
  • 4 high current PWM
  • 3 low current PWM

overcurrent protection only

Additional information

Weight 1 kg
Dimensions 30 × 30 × 10 cm

Reviews

There are no reviews yet.

Be the first to review “Adaptronic M1200 Modular ECU – 4 Cylinder / 2 Rotor”

Your email address will not be published. Required fields are marked *

Post comment